"EdgeRouter X SFP" 修訂間的差異
出自 CH 維基百科
小 (已保護 "EdgeRouter X SFP" ([編輯=僅允許管理員] (無限期)[移動=僅允許管理員] (無限期))) |
|||
| (未顯示由 3 位使用者於中間所作的 18 次修訂) | |||
| 行 1： | 行 1： | ||
| − | + | 註:前方有$#為CLI指令 | |
| − | Port Forwarding | + | '''IPv6 of Hinet pppoe''' |
| + | P.S. eth0為WAN | ||
| + | $sudo su | ||
| + | #configure | ||
| + | #set interfaces ethernet eth0 pppoe 0 ipv6 enable | ||
| + | #set interfaces ethernet eth0 pppoe 0 ipv6 address autoconf | ||
| + | #set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 | ||
| + | #set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 prefix-length 64 | ||
| + | #set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 interface switch0 | ||
| + | #set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 interface switch0 service slaac | ||
| + | #set interfaces ethernet eth0 pppoe 0 ipv6 router-advert link-mtu 1492 | ||
| + | #set interfaces switch switch0 ipv6 router-advert prefix ::/64 | ||
| + | #commit | ||
| + | #save | ||
| + | #exit | ||
| + | #reboot | ||
| + | #y | ||
| + | |||
| + | '''硬體加速''' | ||
| + | #configure | ||
| + | #set system offload hwnat enable | ||
| + | #commit | ||
| + | #save | ||
| + | P.S.建議重啟 | ||
| + | |||
| + | '''Port Forwarding''' | ||
WAN interface pppoe0 | WAN interface pppoe0 | ||
Auto firewall no Enable | Auto firewall no Enable | ||
LAN interface swtch0 | LAN interface swtch0 | ||
| − | WAN_IN | + | '''Firewall Policie'''s |
| − | 新增規則:Basic頁面 Action->Accept Destination頁面 輸入port | + | WAN_IN |
| + | 新增規則:Basic頁面->Action->Accept Destination頁面->輸入port | ||
| + | |||
| + | '''PPPOE Relay''' | ||
| + | #sudo pppoe-relay -S eth0 -C switch0 | ||
| + | |||
| + | '''UPnP''' | ||
| + | Wizards -> UPnP | ||
| + | Internal interface:switch0 External interface:pppoe0 | ||
| + | '''UPnP2''' | ||
| + | $sudo su | ||
| + | #configure | ||
| + | #set service upnp2 wan pppoe0 | ||
| + | #set service upnp2 listen-on switch0 | ||
| + | #set service upnp2 listen-on eth1 | ||
| + | #set service upnp2 nat-pmp enable | ||
| + | #set service upnp2 secure-mode enable | ||
| + | #commit | ||
| + | #save | ||
| + | #exit | ||
| + | '''Restart pppoe''' | ||
| + | #sudo su - | ||
| + | #disconnect interface pppoe0 | ||
| + | #connect interface pppoe0 | ||
| − | + | '''IPsec site to site ''' | |
| − | + | 35.XX.XX.235 為GCP公開IP | |
| + | 10.128.0.0 為GCP內部IP | ||
| + | 118.XX.XX.35 為EdgeRouter公開IP | ||
| + | 172.16.0.0 為EdgeRouter內部IP | ||
| + | [[檔案:IPsec edgeOS to GCP.jpeg]] | ||
| + | [[檔案:IPsec GCP to edgeOS .jpg]] | ||
於 2021年5月24日 (一) 13:14 的最新修訂
註:前方有$#為CLI指令
IPv6 of Hinet pppoe P.S. eth0為WAN $sudo su #configure #set interfaces ethernet eth0 pppoe 0 ipv6 enable #set interfaces ethernet eth0 pppoe 0 ipv6 address autoconf #set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 #set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 prefix-length 64 #set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 interface switch0 #set interfaces ethernet eth0 pppoe 0 dhcpv6-pd pd 0 interface switch0 service slaac #set interfaces ethernet eth0 pppoe 0 ipv6 router-advert link-mtu 1492 #set interfaces switch switch0 ipv6 router-advert prefix ::/64 #commit #save #exit #reboot #y
硬體加速 #configure #set system offload hwnat enable #commit #save P.S.建議重啟
Port Forwarding WAN interface pppoe0 Auto firewall no Enable LAN interface swtch0 Firewall Policies WAN_IN 新增規則:Basic頁面->Action->Accept Destination頁面->輸入port
PPPOE Relay #sudo pppoe-relay -S eth0 -C switch0
UPnP Wizards -> UPnP Internal interface:switch0 External interface:pppoe0 UPnP2 $sudo su #configure #set service upnp2 wan pppoe0 #set service upnp2 listen-on switch0 #set service upnp2 listen-on eth1 #set service upnp2 nat-pmp enable #set service upnp2 secure-mode enable #commit #save #exit
Restart pppoe #sudo su - #disconnect interface pppoe0 #connect interface pppoe0
IPsec site to site 35.XX.XX.235 為GCP公開IP 10.128.0.0 為GCP內部IP 118.XX.XX.35 為EdgeRouter公開IP 172.16.0.0 為EdgeRouter內部IP
